Canon MultiPASS L60 Скачать руководство пользователя страница 247

Страница: 247 / 341

Chapter 11

Frequently Asked Questions

11-23

equently Asked

Questions

Problem

Possible cause

Solution

The MultiPASS L60

ECM receiving on the

If the receiving fax machine

cannot send a fax using receiving fax machine may

does support ECM

ECM?

be turned off.

reception, call the other

(

continued

)

party and have them check
if ECM reception is turned
on.

ECM sending on the

Turn ECM sending on. See

MultiPASS L60 may be

pages 13-8 and 13-9 or the

turned off.

MultiPASS Desktop
Manager

User’s Guide

Errors occur frequently

The phone line may be in

Lower the speed at which

while sending faxes?

poor condition, or you may

the unit starts sending faxes

have a poor connection.

in the TX START SPEED
setting. See pages 13-14 and
13-15 or the MultiPASS
Desktop Manager

User’s

Guide

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 247 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: