Canon MultiPASS L60 Скачать руководство пользователя страница 167

Страница: 167 / 341

Chapter 6

Sending Faxes

6-39

Sending Faxes

Deleting a Document Stored in Memory

Follow this procedure to delete a document from memory.

Press

FUNCTION

, then

MEMORY REF

Press

START/COPY

Use

to select the TX/RX number of the document you want

to delete.

❏

If you are not sure of the TX/RX number of the document you
want to delete, print the list of documents stored in memory.
See page 6-37 for details.

Press

START/COPY

Press

to delete the fax, or

to cancel deleting.

❏

If you press

, the unit returns to step 3.

Press

STOP

to return to standby mode.

14:30 FaxOnly

YES=(

✱

) NO=(#)

TX/RX NO. 0003

TX/RX NO. 0001

DELETE DOCUMENT

MEMORY REFERENCE

FUNCTION

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 167 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: