manualshive.com logo in svg

Canon MultiPASS L60, Руководство пользователя, Страница: 205 / 341

Поделиться
Скачать
Canon MultiPASS L60 Скачать руководство пользователя страница 205

Chapter 8

Special Features

8-5

Special Featur

es

Confirming a Dial Tone*

Use this feature only when you register a number. In some areas you
may have to confirm the dial tone in the middle of the facsimile number
before dialling the rest of the number. This is called dial tone detection.

1.

Use the numeric buttons to enter the first part of the number until
dial tone detection is required.

2.

When a dial tone detection is required, press 

D.T

. 

❏

Where the dial tone is inserted, you will see a small dot. During
dialling this is where the unit waits for the dial tone.

3.

Enter the remainder of the number.

*This feature is ineffective in the UK, Hong Kong, Australia, New Zealand,

Singapore, and Malaysia.

TEL=348•

TEL=        348

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов