Canon MultiPASS L60 Скачать руководство пользователя страница 172

Страница: 172 / 341

6-44

Sending Faxes

Chapter 6

Enter the destination(s) using any of the following three methods.

❏

One-touch speed dialling:

Press the desired one-touch speed dialling button(s).

❏

Coded speed dialling:

Press

CODED DIAL

, then enter the two-digit code (00–99)

using the numeric buttons.

• Be sure to press

CODED DIAL

before each code.

❏

Regular dialling:

Enter the number using the numeric buttons, then press

START/COPY

• You can only enter one number with the numeric buttons.

Press

START/COPY

❏

The MultiPASS L60 begins scanning the document.

SCANNING P.001

01=CANON EUROPE

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 172 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: