Canon MultiPASS L60 Скачать руководство пользователя страница 207

Страница: 207 / 341

Chapter 8

Special Features

8-7

Special Featur

Restricting Use of the MultiPASS L60

If you do not want unauthorised people to be able to make calls, set the
LOCK PHONE feature to ON.

To restrict access to the LOCK PHONE option, you need to register a
password. Set the password and LOCK PHONE option as follows:

Press

FUNCTION

Use

to select SYSTEM SETTINGS.

Press

START/COPY

twice.

❏

If a password has already been registered, enter it now, then
press the

START/COPY

button.

Press

START/COPY

❏

If a password is already

Ex:

registered, it will be displayed:

❏

If a password is not registered,
the following is displayed:

PASSWORD _

PASSWORD 1234

PASSWORD

UN/LOCK PHONE

SYSTEM SETTINGS

FUNCTION

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 207 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: