Canon MultiPASS L60 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 173

Chapter 6

Sending Faxes

6-45

Sending Faxes

Using Alternative Telephone Networks
(UK only)

The MultiPASS L60 has a built-in feature that allows you to send
documents and make telephone calls with an alternative long-distance
service, such as the 2300 Service of Mercury Communications Limited.
If you subscribe to such a service, you can save money on most long
distance international communications.

The procedures described in this section show you how to use your unit
with the 2300 Service of Mercury Communications Limited. For details
on using your unit with alternative telephone services, contact your
Canon authorised representative.

Attaching the M Label

Before operating the unit, attach the M label to help you identify the
button as shown below.

«
...
171
172
173
174
175
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов