Chapter 17
17-72
4. ACC
T-17-58
COPIER>OPTION>ACC
Sub item
Description
level.
COIN
Coin vendor switching
This selects whether to establish the coin vendor control mode.
Settings
0: Coin vendor not used (control cards can be used; not charged)
1: Coin vendor (charged)
2: Remote area counter (charged)
3: Charged by DA
4: Charged by iR
[Factory setting/value after clearing RAM: 0]
Note:
When the setting has been changed to "3" (DA charges), the values of the following items will also be changed.
[Service mode]
- COPIER>OPTION>USER>CONTROL:1
- COPIER>OPTION>USER>AFN-PSWD:1
- COPIER>OPTION>BODY>UI-BOX:0
- COPIER>OPTION>BODY>UI-SEND:0
- COPIER>OPTION>BODY>UI-FAX:0
- COPIER>OPTION>BODY>UI-EXT:0
- COPIER>OPTION>BODY>DA-CNCT:1
[User mode > system control settings]
- Expansion unit settings > expansion unit function priority: ON
- Network settings > email > I fax > SMTP reception: OFF
- Network settings > email > I fax > POP3 reception: OFF
- Network settings > SMB settings > use of SMB printing: 0
- Network settings > TCP/IP settings > use of IPP printing: 0
- Network settings > TCP/IP settings > IP address range setting > printing enable address ON/OFF: ON
Network settings > TCP/IP settings > use of FTP printing: OFF
1
DK-P
Used to set paper size used by paper deck (option).
Setting values
0: A4 [Factory default/After RAM clear]
1: B5
2: LTR
1
CARD-SW
Used to select UI screen when coin vendor is supported.
Setting values
0: Coin [Factory default/After RAM clear]
1: Card
2: Coin + card
1
USB-MSK
Limiting the number of USB-HOST channels on the models with the USB-HOST installed.
Setting values 0 to 2
The relevant channels of the USB-HOST are masked (deactivated).
(e.g.)
When there are two channels of CH0 and CH1,
0: Not mask any channel.
1: Masks CH1.
2: Reserved
1
OUT-TRAY
No.3 delivery tray availability
This is mainly used when the No.2 or No.3 delivery unit is installed. It is set to "1" when the No.3 delivery unit is
installed.
Settings
0: Not available
1: Available
[Factory setting/value after clearing RAM: 0]
1
IN-TRAY
Inner delivery tray availability
This sets the availability of the No.2 delivery tray. It is set to "1" when the No.2 delivery tray is available.
Settings
0: Not available
1: Available
[Factory setting/value after clearing RAM: 0]
1
MIN-PRC
Coin manager minimum value setting
This determines the minimum value handled by the coin manager which is connected. For instance, the service
technician inputs "10" if the minimum value supported by the Japanese yen coin manager is 10 yen.
This item takes effect only when 4 is set for ACC>COIN.
Additional note
When a number from 1 to 4 (Euros, pounds, Swiss francs, dollars) is set for COPIER>OPTION>ACC>UNIT-PRC, a
fractional monetary unit can be input. For instance, an input of "50" signifies 50 cents ($0.50).
Setting range: 0 to 9999
[Factory setting/value after clearing RAM: 10]
1
MAX-PRC
Coin manager maximum value setting
This determines the maximum value handled by the coin manager which is connected. An error screen is displayed if a
value lower than the smallest unit is input when inputting the charge amount using initial settings/registration. For
instance, the service technician inputs "8900" if the maximum value supported by the Japanese yen coin manager is 8900
yen.
This item takes effect only when 4 is set for ACC>COIN.
Additional note
When a number from 1 to 4 (Euros, pounds, Swiss francs, dollars) is set for COPIER>OPTION>ACC>UNIT-PRC, a
fractional monetary unit can be input. For instance, an input of "50" signifies 50 cents ($0.50).
Setting range: 0 to 9999
[Factory setting/value after clearing RAM: 0]
1
Содержание iR C2880 series
