Canon iR C2880 series, Руководство по обслуживанию

Страница: 547 / 610

Chapter 17
17-63
IFAX-SZL Selection of whether to restrict the transmission data size during IFAX transmission
This selects whether to restrict the transmission data size during IFAX transmission (but only when the transmissions do
not go through the server).
Settings
0: The transmission data size is restricted (whether or not the transmissions go through the server).
1: The transmission data size is not restricted (only when the transmissions do not go through the server).
[Factory setting/value after clearing RAM: 1]
Memo: When the item has been set to "0"
- The upper limit is set by user mode > system control settings > communication control settings > email/I-FAX settings
> upper limit of transmission data size.
- The #830 error results when an attempt is made to send data whose size exceeds the upper limit.
2
IFAX-PGD Permitting the divided transmission per page (only when the upper limit of the transmission data size is exceeded).
Settings
0: Not permit the divided transmission per page upon transmission in the IFAX Simple mode.
[Factory default/After RAM clear]
1: Permits the divided transmission per page upon transmission in the IFAX Simple mode.
When setting '1', in the case of exporting the address book data from remote UI, the password of file server is hidden
from the exported file (to avoid leakage of information).
2
MEAPSAFE Switching to MEAP safe mode
Settings
0: Normal mode
1: Safe mode
[Factory setting/value after clearing RAM: 0]
The safe mode refers to the mode in which the system is started up safely by stopping the added MEAP applications and
starting only the system application which is to be started in the initial status. Set the item to "1" to start the system in
the safe mode when system recovery is to be initiated in cases where the MEAP platform does not start up normally due
to contention for resources between MEAP applications or to service registration/utilization sequence, for example.
When the safe mode is established, "MPS" is displayed on the control unit screen.
2
TRAY-FLL Setting the timing to issue an output-tray-full warning.
Settings
0: Issues an output-tray-full warning when all the delivery trays become full.
[Factory default/After RAM clear]
1: Issues an output-tray-full warning when all the specified trays become full.
2
PRNT-POS Switch for selecting whether to temporarily stop the printing of all subsequent jobs when a job is canceled because an
error has occurred
This temporarily stops the PDL printing of all the jobs when job cancel (such as #037) has occurred due to an error inside
the equipment at any time other than a service call.
Settings
0: The printing of all jobs is not temporarily stopped.
1: The printing of all jobs is temporarily stopped.
[Factory setting/value after clearing RAM: 0]
2
AFN-PSWD Limiting access to the User Mode.
Settings
0: Normal mode (Enters the User Mode without asking a password)
[Factory default/After RAM clear]
1: Enters the User Mode after a password matches.
2
PTJAM-RC PDL jam recovery switch
Sets whether to perform recovery print when there is a jam in a PDL job.
Setting values
0: OFF (No recovery)
1: ON (Recovery)
[Factory settings and after RAM clear: 1]
2
SLP-SLCT Switch for selecting use of network-based application
The machine must receive a specific packet in order for it to recover from sleep mode 3 via the network. The existing
network-based application (NetSpot Accountant or imageWARE) that supports BW2/CL1 does not send this packet so
if the machine has been transferred to sleep mode 3 (2w sleep), it cannot recover via the network. When this item is set
to "1," the machine is not transferred to sleep mode 3 (2w sleep), and recovery from the sleep mode via the network is
enabled, but there is a tradeoff in that the power consumption is increased.
Settings
0: The network-based application is not used (the machine is set to the 2w sleep mode).
1: The network-based application is used (the machine is not set to the 2w sleep mode).
[Factory setting/value after clearing RAM: 0]
Memo This is not used with normal servicing.
2
PS-MODE Selection of compatible mode when PS is used (image processing, print specifications)
This selects the machine control when backward compatibility is required by PS. It is a mode which maintains
compatibility in the image processing and print specifications in the face of possible replacement.
Settings
0: The PS-compatible mode is not used.
1: Backward compatibility with PS Type3 Halftone command (dithering increase sequence reversed)
[Factory setting/value after clearing RAM: 0]
2
COPIER>OPTION>USER
Specification selection related to user mode
Sub item Description level.