Canon iR C2880 series, Руководство по обслуживанию

Страница: 530 / 610

Chapter 17
17-46
17.5.2 FEEDER
17.5.2.1 FEEDER Table
0013-9279
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
T-17-53
DEBUG-1 Setting of types of logs to be saved and timing at which they are to be saved on hard disk
This specifies the types of logs to be saved and the timing at which they are to be saved on the hard disk.
Setting range
0: For saving PLOGs. They are saved when Reboot/Exception has been detected.
1: For saving PLOGs. They are saved when Reboot/Exception/Ecode has been detected.
2: For saving SUBLOGs. They are saved when Reboot/Exception/Ecode has been detected.
3: For saving SUBLOGs in the overwrite mode. They are saved when Reboot/Exception/Ecode has been detected.
[Factory setting/value after clearing RAM: 0]
Remarks
Logs of the PLOG type to be saved when "0" or "1" is set can be printed out by selecting
COPIER>FUNCTION>SYSTEM>DEBUG-2. SUBLOGs to be saved when "2" or "3" is set cannot be printed out (they
are uploaded from SST).
MEMO:
- This is not used with normal servicing. (It is used for analyzing trouble causes.)
- To use it, the instructions given by the quality support division must be followed.
2
DEBUG-2 Printout of logs saved on hard disk
This prints out the PLOGs to be saved when "0" or "1" has been set for COPIER>FUNCTION>SYSTEM>DEBUG-1.
Remarks
The SUBLOGs to be saved when "2" or "3" has been set for COPIER>FUNCTION>SYSTEM>DEBUG-1 are not
printed out. The number of printout sheet is about 20 in the A4 size.
MEMO:
- This is not used with normal servicing. (t is used for analyzing trouble causes.)
- To use it, the instructions given by the quality support division must be followed.
2
FEEDER>FUNCTION
Sub item Description level.
MTR-CHK Use it to check the motor and the like of the ADF on its own.
Operation
1) Press [MOTOR-CHK] to highlight.
2) Enter the number of the component using the keypad.
3) Press the OK key.
4) Press [MOTOR-ON[ to start checking the operation.
Settings
0: pickup motor
1: feed motor
2: delivery reversal motor
3: lock motor
[Factory default/After RAM clear: 0]
1
TRY-A4 Use it to execute automatic adjustment (A4 Width) for DF original paper width detection. 1
TRY-A5R Use it to execute automatic adjustment (A5R width) for DF original paper width detection. 1
TRY-LTR Use it to execute automatic adjustment (LTR width) for DF original paper width detection. 1
TRY-LTRR Use it to execute automatic adjustment (LTR-R width) for DF original paper width detention. 1
FEED-CHK Use it to check paper movement in the ADF on its own.
Operation
1) Press [FEED-CHK] to highlight.
2) Enter the number of the component using the keypad.
3) Press the OK key.
4) Press [FEED-ON] to start checking the operation.
Feed Mode
0: single-sided operation
1: double-side operation
2: single-sided operation w/ stamp
3: double-sided operation w/ stamp
[Factory default/After RAM clear: 0]
1
SL-CHK Use it to check the ADF solenoid on its own.
Operation
1) Press [SL-CHK] to highlight
2) Enter the number of the component using the keypad.
3) Press the OK key.
4) Press [SL-ON] to start checking the operation.
Number of Component
0: lock solenoid
1: stamp solenoid
[Factory default/After RAM clear: 0]
1
COPIER>FUNCTION>SYSTEM
Sub item Description level.