Canon iR C2880 series, Руководство по обслуживанию

Страница: 158 / 610

Chapter 4
4-18
3) Remove the HDD.
(page 4-18)
[Removing the HDD]
4.7.10.2 Removing the Image Memory (SDRAM) PCB
0014-2531
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1) Remove the 2 HDD mounts [2].
- 2 screws [1] each
F-4-36
2) Open the fixing member in the direction shown by the arrow, and then
remove the image memory (SDRAM) PCB [1].
In case the 2 image memories (SDRAM) are attached, remove both of them.
F-4-37
F-4-38
4.7.11 HDD
4.7.11.1 Before Removing the HDD
0013-6788
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1) Detach the rear upper cover.
(page 10-14)
[Detaching the Rear Upper
Cover]
2) Detach the left rear cover. (page 10-14) [Detaching the Left Rear Cover]
4.7.11.2 Removing the HDD
0013-6787
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1) Detach the main controller cover [1].
- 14 screws [2]
F-4-39
2) Remove the HDD unit [1].
-2 connectors [2]
-6 screws [3]
- 1 cable clamp [4]
F-4-40
Points to Note when Removing the HDD
When removing the HDD, be sure not to damage it by electrostatic dis-
charge.
Do not give a shock to the HDD.
4.7.11.3 When Replacing the HDD
0014-3124
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
1. If NetSpot Accountant (NSA) Is Not Used
1) Formatting the HDD
While holding down the 2 and 8 keys on the control panel, turn on the
power to start up. Using the HD formatting function of the SST, format
all partitions.
2) Downloading the Software
Using the SST, download the various software (system, language, RUI).
The machine will take about 10 min to start up after downloading.
2. If NetSpot Accountant (NSA) Is Used Together with a Card Reader
The card ID used by the NSA resides on the HDD. If you have replaced the
HDD, therefore, you will have to newly download the card data from NSA
to enable the statistical operations of NSA. After going through steps 1) and
2) above, perform the following:
1) Set the following in service mode:
Select the following : COPIER >FUNCTION >INSTALL >CARD; then,
enter the number of the first card, and press [OK].
(For instance, if cards No. 1 through No. 1000 are used for group control,
enter '1')
2) Turn off and then on the machine; when the machine has started up,
perform the following in user mode:
Select the following : user mode >system control settings >group ID
control >count control; then, check that IDs from 00000001 through
00001000 have been prepared.
Select the following : user mode >system control settings >network
settings >TCP/IP settings >IP address; then, set up 'IP address' 'gateway
address' and 'subnet mask'
Select the following : user mode >system administrator setup; then, fill in
'system control group ID' and 'system control ID No.' thereafter, turn off
and then on the machine.
If you leave out 'system control group ID' and 'system control ID No.' the
service engineer will not be able to 'register card to device' as part of setup
work for NSA.
3) With the machine in standby state, download the card ID to be used from
NSA.
[1] [1] [2]
[1] [1] [2]
[1]
[1]
[1]
[2]
[2]
[2]
[2]
[1]
[2] [3]
[3]
[4]