Canon iR C2880 series, Руководство по обслуживанию

Страница: 283 / 610

Chapter 8
8-21
COPIER > ADJUST > CST-ADJ > MF-A4R
COPIER > ADJUST > CST-ADJ > MF-A6R
COPIER > ADJUST > CST-ADJ > MF-A4
8.7 Registration Unit
8.7.1 Overview
0014-0324
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
The registration roller is driven with the registration multi motor (M6).
The registration clutch (CL6) is located between the registration roller and the registration multi motor, and it controls ON/OFF of the registration roller in order to
match a paper and an image on the drum at the predetermined registration point.
F-8-25
8.7.2 Control of Registration Unit
0014-2910
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
In this machine, it is controlled to turn OFF the pickup motor (in case of cassette pickup), manual feeder pickup clutch (in case of manual feeder pickup), and the
duplexing feeding motor (in case of duplexing re-pickup) to make papers stop at the point where the distance from the pre-registration sensor to the registration
roller (19.9 mm) + predetermined registration arching (cassette/duplexing: 3 mm, manual feed: 5.5 mm) are added after the pre-registration sensor detects the lead-
ing edge.
When executing the accelerated pickup (300 mm/sec), decelerate to 200 mm/sec when the pre-registration sensor turns ON.
When the registration clutch turns ON, the registration roller starts to rotate and feeds paper to the secondary transfer assembly.
The registration clutch is turned OFF either after a paper is fed the predetermined amount (paper 50ms) or when the next paper turns ON the pre-registration
sensor.
8.7.3 Checking Horizontal Registration
0014-0325
/ / / / iR C3380i / iR C3380 / iR C2880i / iR C2880
The machine does not have the horizontal registration adjustment function by the horizontal registration detection at the time of duplexing feeding.
However, practically, adjustment of the horizontal registration point is possible by adjusting the write start timing of the horizontal scanning of the laser (horizontal
scanning interval signal) in terms of software in the service mode setting.
In the service mode, set the horizontal registration adjustment value for each source of paper. The range of adjustment value is +/-2.5 mm. In case of duplexing re-
pickup, the write start timing of the horizontal scanning of the laser is corrected in accordance with the horizontal registration adjustment value of the source of
paper.
Service Mode:
COPIER>ADJUST>FEED-ADJ>ADJ-REFE
Use it to adjust the horizontal registration for the 2nd side of small-size double-sided prints.
COPIER>ADJUST>FEED-ADJ>ADJ-RE-L
Use it to adjust the horizontal registration for the 2nd side of large-size double-sided prints.
COPIER>ADJUST>FEED-ADJ>LOOPREFE
Use it to adjust the degree of arching for the 2nd side of double-sided prints.
The term "2nd side of a double-sided print" as used in relation to the machine's service mode refers to the side that receives an image second in order; in other words,
it corresponds to the 1st side of the original.
Reference:
Small paper: a paper whose length of paper feeding direction is LTR (216 mm) or shorter, e.g., A4 and B5.
Large paper: a paper whose length of paper feeding direction is longer than LTR (261 mm), e.g., A3, A4R, and B5R.
M6
J313
J314
CL6
DC controller PCB
Registr
ation m
ulti motor dr
iv
e signal
Registr
ation clutch dr
iv
e signal