BLEMO ER40-G Скачать руководство пользователя

Страница: 71 / 242

[1.4 MOTOR CONTROL]

(drC-)

Encoder check procedure

Set up in open-loop mode, following the recommendations on page

Set

[Encoder usage]

(EnU)

[No]

(nO)

Set

[Encoder type]

(EnS)

and

[Number of pulses]

(PGI)

accordingly for the encoder used.

Set

[Encoder check]

(EnC)

[Yes]

(YES)

Check that the rotation of the motor is safe.

Set the motor rotating at stabilized speed

≈

15% of the rated speed for at least 3 seconds, and use the

[1.2-MONITORING]

(SUP-)

menu to monitor its behavior.

If it trips on an

[Encoder fault]

(EnF)

[Encoder check]

(EnC)

returns to

[No]

(nO)

- Check

[Number of pulses]

(PGI)

and

[Encoder type]

(EnS).

- Check that the mechanical and electrical operation of the encoder, its power supply and connections are all correct.
- Reverse the direction of rotation of the motor (

[Output Ph rotation]

(PHr)

parameter page

) or the encoder signals.

Repeat the operations from 5 onwards until

[Encoder check]

(EnC)

changes to

[Done]

(dOnE)

(1) The encoder parameters can only be accessed if the encoder card has been inserted, and the available selections will depend

on the type of encoder card used. The encoder configuration can also be accessed in the

[1.5- INPUTS / OUTPUTS CFG]

(I/O)

menu.

Code

Name/Description

Adjustment range

Factory setting

EnC

• [Encoder check]

[Not done]

(nO)

YES

dOnE

Encoder feedback check See the procedure below.
The parameter can be accessed if an encoder card has been inserted (1).

[Not done]

(nO)

Check not performed.

[Yes]

(YES)

: Activates monitoring of the encoder.

[Done]

(dOnE)

: Check performed successfully.

The check procedure checks:

- The direction of rotation of the encoder/motor
- The presence of signals (wiring continuity)
- The number of pulses/revolution

If a fault is detected, the drive locks in

[Encoder fault]

(EnF)

fault mode.

EnU

• [Encoder usage]

[No]

(nO)

SEC

rEG

PGr

The parameter can be accessed if an encoder card has been inserted (1).

[No]

(nO)

: Function inactive

[Fdbk monit.]

(SEC)

: The encoder provides speed feedback for monitoring only.

[Spd fdk reg.]

(rEG)

: The encoder provides speed feedback for regulation and monitoring. If

[Motor control

type]

(Ctt)

[SVC U]

(UUC)

the encoder operates in speed feedback mode and enables static correction of

the speed to be performed. This configuration is not accessible for other

[Motor control type]

(Ctt)

values.

[Speed ref.]

(PGr)

: The encoder provides a reference.

Содержание ER40-G



















































































































































































































































Результаты поиска

Содержание ER40-G

Отзывы:

Похожие инструкции для ER40-G

Бренды по названию

Популярные бренды

BLEMO ER40-G, Руководство по программированию

Результаты поиска

Содержание ER40-G

Отзывы:

Похожие инструкции для ER40-G

Бренды по названию

Популярные бренды