BLEMO ER40-G, Руководство по программированию

Страница: 223 / 242

223
Faults – Causes – Remedies
Faults that can be reset with the automatic restart function, after the cause has disappeared
(continued)
Fault Name Probable cause Remedy
OPF2 [3 motor phase loss] • Motor not connected or motor
power too low
• Output contactor open
• Instantaneous instability in the
motor current
• Check the connections from the drive to the motor
• If an output contactor is being used, parameterize
[Output
Phase Loss] (OPL) = [Output cut] (OAC) , page 178
• Test on a low power motor or without a motor: In factory
settings mode, motor phase loss detection is active [Output
Phase Loss] (OPL) = [Yes] (YES) . To check the drive in
a test or maintenance environment, without having to use
a motor with the same rating as the drive (in particular for high
power drives), deactivate motor phase loss detection
[Output
Phase Loss] (OPL) = [No] (nO)
• Check and optimize the [IR compensation] (UFr) page 68 ,
[Rated motor volt.] (UnS) and [Rated mot. current] (nCr)
parameters, page 61 , and perform [Auto tuning] (tUn) ,
page 63 .
OSF [Mains overvoltage] • Line voltage too high
• Disturbed line supply • Check the line voltage
OtF1 [PTC1 overheat] • Overheating of the PTC1 probes
detected
• Check the motor load and motor size
• Check the motor ventilation
• Wait for the motor to cool before restarting
• Check the type and state of the PTC probes
OtF2 [PTC2 overheat]
• Overheating of the PTC2 probes
detected
OtFL [LI6=PTC overheat]
• Overheating of PTC probes
detected on input LI6
PtF1 [PTC1 probe]
• PTC1 probes open or short-
circuited
• Check the PTC probes and the wiring between them and the
motor/drive
PtF2 [PTC2 probe]
• PTC2 probes open or short-
circuited
PtFL [LI6=PTC probe]
• PTC probes on input LI6 open or
short-circuited
SCF4 [IGBT short circuit]
• Power component fault • Perform a test via the [1.10 DIAGNOSTICS] menu.
• Inspect/repair the drive
SCF5 [Motor short circuit]
• Short-circuit at drive output • Check the cables connecting the drive to the motor, and the
motor’s insulation
• Perform tests via the [1.10 DIAGNOSTICS] menu.
• Inspect/repair the drive
SLF1 [Modbus com.]
• Interruption in communication on
the Modbus bus
• Check the communication bus
• Check the time-out
• Refer to the Modbus User's Manual
SLF2 [PowerSuite com.]
• Fault communicating with
PowerSuite
• Check the PowerSuite connecting cable
• Check the time-out
SLF3 [HMI com.]
• Fault communicating with the
graphic display terminal
• Check the terminal connection
• Check the time-out
SPIF [PI Feedback]
• PID feedback below lower limit • Check the PID function feedback.
• Check the PID feedback supervision threshold and time delay,
page 147 .
SSF [Torque/current lim]
• Switch to torque limitation • Check if there are any mechanical problems
• Check the parameters of
[TORQUE LIMITATION]
(tLA-) page 155 and the parameters of the
[TORQUE OR I LIM. DETECT.] (tId-) fault, page 187 ).
tJF
[IGBT overheat]
• Drive overheated • Check the size of the load/motor/drive
• Reduce the switching frequency
• Wait for the motor to cool before restarting
ULF [Proc. Underload Flt] • Process underload • Check and remove the cause of the underload.
• Check the parameters of the
[PROCESS OVERLOAD] (ULd-)
function, page 191 .