APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 178 / 379

Removing the engine from the vehicle

•

Carry out the operations described un-

der Vehicle preparation.

•

Support the engine by means of belt

and hoist.

•

Working on the left side, unscrew and

remove the two upper nuts.

•

Working on the right side, slightly slide

off the two upper bolts.

•

Collect the spacers on the opposite

side.

•

Check spacers length so as not to in-

terchange them upon refitting

•

Remove the two upper bolts and col-

lect the washers.

Engine from vehicle

DORSODURO FACTORY ABS

ENG VE - 178

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды