APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 213 / 379

Check the valve eccentricity:

valve stem (3) maximum eccentricity allowed:

0.05 mm (0.00197 in)

valve head (4) maximum eccentricity allowed:

0.05 mm (0.00197 in)

Check that the fixing grooves (5) of the valve cot-

ters are in proper conditions.

VALVE SPRINGS

Carry out a measurement and a visual inspection

of the valve springs for damage, distortion or loss

of tension.

Measure the spring length at release position.

Valve springs:

minimum wear limit (6) 42.5 mm

(1.673 in).

Valve springs:

minimum wear limit (7) 38 mm

(1.496 in).

Checking the cylinder head

•

Using a round scraper, clean off any carbon deposits in the combustion chamber.

CAUTION

DO NOT USE A POINTED INSTRUMENT TO AVOID DAMAGING OR SCRATCHING THE SPARK
PLUG THREADS OR THE VALVE SEATS.

•

Check the head for damage or scratches and replace it if necessary.

•

Check there are no mineral deposits or rust in the head water cooled jacket; clean off if

required.

•

Use a checking ruler and a thickness gauge positioned diagonally to the ruler to measure

the cylinder head distortion.

Maximum cylinder head distortion: 0.03 mm (0.0012 in)

•

Check that the tappet covers and the camshaft toothed wheel cover are not damaged or

worn; replace the defective part(s).

Installing the overhead camshaft

The camshaft refitting procedure is described in the "Timing" section.

See also

Timing

DORSODURO FACTORY ABS

Engine

ENG - 213

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды