APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 111 / 379

98789

If the code is incorrect, the following message is displayed:

•

INCORRECT CODE

and the instrument panel goes back to the main menu. Otherwise, the following menu is displayed:

•

Exit

•

ECU diagnosis

•

INSTRUMENT PANEL ERRORS

•

Error Clearing

•

VEHICLE SERVICING RESET

•

Update

•

CHANGE KEYS

•

KM / MILES

ECU diagnosis

In this mode a chart is displayed showing potential

errors in the control unit.

IT IS NECESSARY TO REFER TO THE ERROR

INDICATIONS GIVEN BY NAVIGATOR FOR

THIS VEHICLE.

The instrument panel does not keep all previous errors stored in its memory.

INSTRUMENT PANEL ERRORS

In this mode, a chart is displayed showing potential

errors in the immobilizer and the sensors connec-

ted to it.

Instrument panel errors

In this mode, a chart is displayed showing potential errors in the immobilizer and the sensors connected

to it.

DSB 01

- Immobilizer fault: key code read but not recognised.

DSB 02

- Immobilizer fault: key code not read (key not present or transponder not working)

DSB 03

- Immobilizer fault: aerial not working (open or short-circuited)

DSB 04

- Internal controller fault

DSB 05

- -

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 111

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды