APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 370 / 379

Carry out the listed checks before delivering the motorcycle.

WARNING

HANDLE FUEL WITH CARE.

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

- Dirt

Tightening torques inspection

- Safety fasteners:

front and rear suspension unit

front and rear brake calliper retainer unit

front and rear wheel unit

engine - chassis retainers

steering assembly

- Plastic parts fixing screws

Electrical system

- Main switch

- Headlamps: high-beam lights, low-beam lights, tail lights (front and rear) and their warning lights

- Headlight adjustment according to regulations in force

- Front and rear stop light switches and their bulbs

- Turn indicators and their warning lights

- Instrument panel lights

- Instrument panel: fuel and temperature indicator (if present)

- Instrument panel warning lights

- Horn

- Electric start-up

- Engine stop via emergency stop switch and side stand

- Helmet compartment electrical opening switch (if present)

Pre-delivery

DORSODURO FACTORY ABS

PRE DE - 370

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды