APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 290

Страница: 290 / 379

TEERING

RING

NUT

pos.

Description

Type

Quantity

Torque

Notes

Headstock ring nut - pre-tightening

M25x1

30 Nm (22.13 lbf ft)

Steering package

settlement

Headstock ring nut - tightening

M25x1

12 Nm (8.85 lbf ft)

•

Fit the entire fork upper plate, adjusting

with short taps with a rubber hammer

•

Tighten the nut to the specified torque.

•

Tighten the fixing screws of the upper

plate to the prescribed tightening tor-

que.

TEERING

UPPER

PLATES

pos.

Description

Type

Quantity

Torque

Notes

Headstock nut

M22x1

100 Nm (73.76 lbf ft)

Stainless steel TCC screw fastening
stanchions to upper and lower yokes

M8x30

25 Nm (18.44 lbf ft)

When refitting the U-bolt, position the two referen-

ces facing the front part of the vehicle.

OPTION 02

- Steering upper plate

with

a headstock cut.

Suspensions

DORSODURO FACTORY ABS

SUSP - 290

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды