APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 233 / 379

•

Fit a new gasket between the cylinder

and the head.

•

Couple the cylinder and the head.

•

Screw without tightening the two

screws on the outlet side.

•

Screw without tightening the screw on

the intake side.

•

Tighten the cylinder-head fixing

screws to the prescribed torque.

•

Place the cylinder-head unit on the

crankcase stud bolts.

Installing the head cover

CAUTION

BEFORE REFITTING HEAD COVERS, CLEAN HEAD AND COVER SURFACES CAREFULLY.

•

Apply THREEBOND on the head cover

perimeter along the gasket housing.

DORSODURO FACTORY ABS

Engine

ENG - 233

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды