APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 232

Страница: 232 / 379

020714Y

Dial gauge mounting

•

Rotate the crankshaft up to the TDC

(the reversal point of the dial gauge ro-

tation).

•

Lock the crankshaft at TDC using the

specific tool.

•

Calculate the difference between the

two measurements: using the chart be-

low, identify the thickness of the cylin-

der base gasket to be used upon

refitting. By correctly identifying the cyl-

inder base gasket thickness, an ade-

quate compression ratio can be main-

tained

•

Remove the specific tool and the cyl-

inder.

Specific tooling

020720Y

Timing tool

ASE

GASKET

Specification

Desc./Quantity

Measured protrusion -0.10 / + 0.0 mm (- 0.0039 / 0.0000 in)

Gasket 0.4 mm (0.0157 in)

Measured protrusion 0.05 / 0.10 mm (0.0020 / 0.0039 in)

Gasket 0.5 mm (0.0197 in)

Measured protrusion 0.15 / 0.30 mm (0.0059 / 0.0118 in)

Gasket 0.6 mm (0.0236 in)

Installing the cylinder head

•

Place the fixed chain tensioner slider

on the cylinder timing chain compart-

ment, opposite to the chain tensioner.

Engine

DORSODURO FACTORY ABS

ENG - 232

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды