APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 288

Страница: 288 / 379

TEERING

- O

PTION

pos.

Description

Type

Quantity

Torque

Notes

Headstock ring nut - pre-tightening

M25x1

30 Nm (22.13 lbf ft)

Steering package

settlement

Headstock ring nut - tightening

M25x1

12 Nm (8.85 lbf ft)

Headstock cap

M22x1

100 Nm (73.75 lbf ft)

Stainless steel TCC screw fastening
stanchions to upper and lower yokes

M8x30

25 Nm (18.44 lbf ft)

TCEI screw fastening lower clamp

onto fork yoke

M10x60

50 Nm (36.88 lbf ft)

OPTION 02

- Steering upper plate

with

a headstock cut.

TEERING

- O

PTION

pos.

Description

Type

Quantity

Torque

Notes

Headstock ring nut - pre-tightening

M25x1

30 Nm (22.13 lbf ft)

Steering package

settlement

Headstock ring nut - tightening

M25x1

12 Nm (8.85 lbf ft)

Headstock nut - pre-tightening

M22x1

10 Nm (7.37 lbf ft)

Loctite 243

Headstock nut

M22x1

25 Nm (18.44 lbf ft)

Loctite 243

Stainless steel TCC screw fastening
stanchions to upper and lower yokes

M8x30

25 Nm (18.44 lbf ft)

TCEI screw fastening lower clamp

onto fork yoke

M10x60

50 Nm (36.88 lbf ft)

Adjusting play

•

Place the vehicle so that the front wheel is off the ground.

•

Carry out a handlebar rotation test, using a dynamometer at the handgrip external end.

•

The handlebar resistance to rotation must be of 400 ± 150 g (0.88 ± 0.33 lb) in both directions.

•

Adjust if clearance is detected.

OPTION 01

- Steering upper plate

without

a headstock cut.

•

Unscrew and remove the U-bolt four

fixing screws.

•

Remove the U-bolt.

•

Remove the handlebar and place it

paying attention that oil in the clutch

and front brake tanks does not spill out.

Suspensions

DORSODURO FACTORY ABS

SUSP - 288

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды