APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 148 / 379

•

If shorted to positive: excessive voltage has been detected at PIN B5 of the throttle control

unit. If the circuit is open, shorted to negative: voltage equal to zero has been detected at

PIN B5 of the throttle control unit.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the Rear throttle Potenti-

ometer 2 (voltage): disconnect the left connector and see the value displayed by Navigator:

if the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle

body if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle body connector and the throttle

valve connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body.

Front throttle supply voltage during self-acquisition P0164

Example value:

low supply voltage

Error cause

•

The throttle power supply voltage is too low to carry out the self-acquisition test correctly (at

each key ON). The instrument panel does not indicate the presence of this error even in the

ATT status.

Troubleshooting

•

The throttle test is not carried out when the key is set to ON because the test could show

unreal errors (because the voltage is too low). Voltage is detected by the Marelli control unit.

Front throttle control circuit P0166

Example value:

short circuit to positive / short circuit to negative / open circuit, overvoltage, excessive

internal temperature.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN C1 of the throttle control

unit connector. If shorted to negative: no voltage has been detected. If the circuit is open:

an interruption has been detected.

Troubleshooting

•

shorted to positive: disconnect the throttle body connector, set key to ON and check voltage

at PIN 3: if the voltage read is higher or equal to 5V, there is a short circuit on the cable

harness; replace the throttle body if the voltage is null

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 148

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды