manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 221

•

Remove the camshaft, lock it on a vice

with aluminium jaws, then tighten it to

the prescribed torque.

DO NOT TIGHTEN THE CAMSHAFT GEAR NUT TO THE
ULTIMATE TIGHTENING TORQUE WITH THE SHAFT
MOUNTED ON THE CYLINDER.
THIS OPERATION WOULD IRRETRIEVABLY DAMAGE
THE HEAD .

Locking torques (N*m)

Nut fixing camshaft gears - M15x1 (4)

 

90 Nm

(66.38 lbf ft)

•

Remove the gear alignment tool.

Specific tooling

020718Y

 

Camshaft gear alignment pin

•

Release the crankshaft from the specific special tool.

•

Rotate the crankshaft in the riding direction until the rear cylinder piston reaches the top

dead centre.

•

Lock the crankshaft with the specific special tool.

•

Carry out the timing operations performed for the front cylinder.

Specific tooling

020720Y

 

Timing tool

Cylinder-piston assembly

DORSODURO FACTORY ABS

Engine

ENG - 221

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды