APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 225

Страница: 225 / 379

Checking the cylinder

•

All seal surfaces must be clean and flat.

•

Make sure all threads are in proper conditions.

•

Check cylinder sliding surface for signs of friction and scratches. Also check the seal sur-

faces for damages.

CAUTION

IF THE GROOVES ON THE CYLINDER LINER ARE EVIDENT, REPLACE THE CYLINDER AND
THE PISTON.

•

Clean off lime scales on the cylinder

cooling slots.

•

Measure the cylinder bore at a dis-

tance of 10 - 43 - 90 mm (0.39 - 1.69 -

3.54 in) from the head coupling sur-

face; the highest value should be

considered to estimate wear limits.

Cylinder bore "C": 92.000 mm (3.6220 - in) C=

D1 or D2 max

Cylindricity tolerance: 0.020 mm (0.00079 in)

Replace the cylinder, the piston and the piston ring

all together if not complying with specifications.

Checking the piston

•

Measure the piston skirt diameter "P"

with a micrometer (a=10 mm (0.39 in)

from the piston lower border).

•

Calculate the clearance between pis-

ton and cylinder as follows:

Piston - cylinder clearance C = C - P

Piston - cylinder clearance: 0.050 - 0.064 mm

(0.00197 - 0.00252 in) Limit: 0.100 mm (0.00039

in)

•

Replace the cylinder, the piston and

the piston ring all together if not com-

plying with specifications.

DORSODURO FACTORY ABS

Engine

ENG - 225

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды