APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 280 / 379

•

Remove the retainer ring.

•

Take out the sleeve from the stem using the stem as a hammer puller.

•

Remove the fixed bushing (1), the

movable bushing (2), the ring (3) and

the oil seal (4) from the stem.

•

Remove the lock seeger ring of the

spring guide.

•

Remove the spring guide.

•

Using a hook spanner lock the pump-

ing member pin

•

Remove the stem bottom screw.

Specific tooling

020889Y

Pumping member ring nut locking

spanner

Suspensions

DORSODURO FACTORY ABS

SUSP - 280

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды