APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя | Manualshive

Страница: 158 / 379

background image

•

Indication on Navigator always released: check the correct position of the cable terminals

on the connector and the correct connection of the cables on the terminals. If they are not

correct, restore the cable harness; if correct, disconnect the two terminals from the sensor

and, with key set to ON, check continuity to ground connection of PIN 2: if there is no con-

tinuity, restore the cable harness; if there is, replace the sensor

•

Indication on Navigator always pulled: disconnect the terminals from the sensor and check

if there is continuity between the two PINS, with clutch released: if there is continuity, replace

the sensor. If the circuit is open, it means that the brown/purple cable from sensor PIN 1 to

ENGINE connector PIN 50 is shorted to ground: restore the cable harness

Side stand sensor

SIDE STAND SENSOR

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfol-

ded, and therefore the circuit is open, the control

unit does not enable vehicle start-up or shuts off

the engine if it is rotating.

Level in electrical circuit diagram:

Start-up ena-

bling switches

Location:

•

on the vehicle: on the side stand

•

connector: left side, near the Marelli

control unit

Electrical characteristics:

•

Side Stand Up: closed circuit (continu-

ity)

•

Side Stand Down: open circuit (infinite

resistance)

Pin-out:

1. Ground connection

2. Voltage 12V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: STATUSES

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 158

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
156
157
158
159
160
...
»

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренд: Cannondale Страницы: 61

Бренд: BMW Страницы: 288

Бренд: KTM Страницы: 38

Бренд: AFX Страницы: 112

WOLVERINE R MAX 2021

Бренд: Yamaha Страницы: 190

Бренд: Yamaha Страницы: 194

WOLVERINE RMAX2 2024

Бренд: Yamaha Страницы: 196

Vstar XVS650T 2004

Бренд: Yamaha Страницы: 101

Бренд: GAS GAS Страницы: 144

640 LC4 Adventure

Бренд: KTM Страницы: 59

Бренд: Ericsson Страницы: 44

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды