APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 219

Страница: 219 / 379

If necessary, remove the timing system gears from

the camshafts:

•

Place the camshaft with the timing sys-

tem gear on a vice and protect the

cams of the camshaft adequately.

•

Unscrew and remove the nut.

ANTICLOCKWISE NUT FOR BOTH REAR CYLINDER
SHAFTS, AN ANTICLOCKWISE ARROW HAS BEEN
PUNCHED ON IT.

•

Collect the washer.

•

Remove the timing system gear from

the camshaft.

•

Clean gears surfaces (camshaft cone and gear cone) with: "System MC 217 spray metal

cleaner".

•

Pre-fit the gear on the camshaft, so that it can turn freely.

•

Place the two camshafts in the head seats and align the two camshaft holes with the head

holes.

•

Align the clearance recovery gear to

the main timing system gear using the

specific tool.

Specific tooling

020718Y

Camshaft gear alignment pin

DORSODURO FACTORY ABS

Engine

ENG - 219

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды