APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 324 / 379

SETTINGS screen page

This screen page is used to adjust some control

unit parameters.

ADJUSTMENTS

Characteristic

Value/example

Unit of

measure

ment

Notes

Coding (1)

Used for re-coding the control unit or coding a new

one.

Coding (2)

Vehicle identification is done according to the con-

nection of PINS 2 and 15 of the ABS control unit

connector and is stored in the control unit memory.

Coding (3)

The identification can be read in the INFO ECU

screen page in the line: Vehicle code.

NOTE: the "X" in the table identifies the con-

nector pin is grounded.

Braking system

DORSODURO FACTORY ABS

BRAK SYS - 324

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды