manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 105

TABLE ZH

27. Fasten the cable harness with a clamp.

Insert the housing as shown in the figure.

Back side

CAUTION

ONCE THE ELECTRICAL SYSTEM IS REFITTED, THE CONNECTORS RECONNECTED AND
CLAMPS AND RETAINERS RESTORED, CARRY OUT THE CHECKS INDICATED UNDER "SPE-
CIAL CHECKS FOR THE CORRECT CONNECTION AND LAYING OF CABLES" IN THE "ELEC-
TRICAL SYSTEM INSTALLATION" SECTION.

TABLE A - Taillight cable harness fitting

1. 2.5x98 (0.10x3.86) Clamp

2. 4.5x180 (0.18x7.08) Clamp

TABLE B - Rear wheel speed sensor fitting

3. Clamps.

4. Cable grommets.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 105

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды