manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 246

•

To reduce the installation force neces-

sary, score an incision approximately

0.5 mm (0.02 in) deep (without cutting

into the steel shell) in each semi-bush-

ing in the area indicated in the figure.

•

Remove the bushings with the crank-

case cold, using a press and the spe-

cific tool and pushing inward from the

outside of the crankcase.

Specific tooling

020726Y

 

Extractor for bushings

Installing

•

The orientation of the semi-bushings

must match the specifications indica-

ted in the drawing as closely as possi-

ble.

NOTE

WHEN REPLACING THE SEMI-BUSHINGS ALONE, THE
NEW COMPONENTS MUST BE THE SAME COLOUR AS
THE REMOVED COMPONENTS. IF THE COLOUR OF THE
OLD COMPONENTS IS NO LONGER VISIBLE, USE THE
TABLE TO IDENTIFY THE CORRECT COMPONENTS, RE-
FERRING TO THE CRANKCASE AND CRANKSHAFT
CLASSES.

Key:

* Semi-bushing joint line

•

Fit the new bushings with the crank-

case cold, using a press and the spe-

cific tool and pushing outward from the

inside of the crankcase, until the punch

comes into contact with the crankcase

surface.

Specific tooling

020727Y

 

Punch for bushings

Engine

DORSODURO FACTORY ABS

ENG - 246

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды