APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 316 / 379

5. Rear brake pump

6. Rear brake pedal control

7. ABS CONTROL UNIT

8. Rear brake calliper

9. Front calliper (2 callipers)

10.Front brake circuit intake solenoid valve (normally open)

11.Humidifier

12.Rear brake circuit intake solenoid valve (normally open)

13.Rear brake exhaust circuit solenoid valve (normally closed)

14.Rear/front brake circuit low pressure accumulator

15.Front brake exhaust circuit solenoid valve (normally closed)

16.DC electric motor

17.Double circuit hydraulic pump (ABS)

18.Rear brake reservoir

19.Front brake reservoir

ABS OPERATION

General specifications:

The front circuit is similar to the rear circuit.

•

The ABS inlet valve (10 - 12) is normally open and it is closed only when the system inter-

venes to avoid wheel locking.

•

The outlet valve (13 - 15) is normally closed and it is opened only when the system intervenes

to avoid wheel locking.

•

When the system is standby, the ABS processor never stops monitoring the speed of the

wheels in order to assess potential wheel slippage.

•

When in standby, the system does not intervene at all when the rider brakes; the braking

system is the same as the one without ABS.

Stages in ABS cycle (the following operations refer to the front circuit but are also applicable to

the rear one):

A - Brake activation: the rider starts braking

as he would usually do.

B - Pressure reduction:

it coincides with danger recognition (wheel slippage above threshold): the

system closes the inlet valve (10-12) and opens the outlet valve (13-15) temporarily.

At this stage the rider cannot increase the pressure on the callipers (8-9) and the system reduces the

pressure on the callipers partially. The excess fluid temporarily fills the front reservoir (18-19) until the

ABS pump (17) self-activates and delivers the fluid back to the brake pump (2-5).

C - Pressure maintained:

the pressure in the callipers (8-9) remains low until total recovery of speed /

wheel grip.

The system restores the fluid taken from the calliper (8-9) in the section of the system between the

brake pump (2-5) and the ABS inlet valve (10-12).

Braking system

DORSODURO FACTORY ABS

BRAK SYS - 316

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды