APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 101

Страница: 101 / 379

TABLE S

15. Side stand switch output sheath

16. Battery compartment breather pipe

17. Cable grommet

TABLE T

The cables fastened to the engine ground must

face downwards.

18. Main cable harness engine ground on the left

19. Battery ground lead on the right

TABLE U

2 4.5x180 (0.18x7.08) Clamps

TABLE V - LAMBDA PROBE

Place the cable harness of the lambda probe in the cable grommet on the clutch crankcase.

20. Fasten the cable harness to the chassis with the clamp.

21. Place the cable harness of the lambda probe behind the cable grommet on the clutch crankcase.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 101

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды