APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 209

Страница: 209 / 379

pos.

Description

Type

Quantity

Torque

Notes

Nut fastening Stud Bolts / Head

26 Nm (19.18 lbf ft)

Bleed union fastener screw

6.5 Nm (4.79 lbf ft)

Water bleed union (steel)

3.50 Nm (2.58 lbf ft)

Loctite 243

Water bleed union (brass)

2 Nm (1.48 lbf ft)

Loctite 243

Removing the overhead camshaft

•

Remove the clutch side crankcase

half.

•

Rotate the crankshaft until the rear cyl-

inder reaches the TDC.

First remove the rear head cover in order to re-

move the rear head camshafts.

First remove the front head cover in order to re-

move the front head camshafts.

Mark the head camshafts, the corresponding

sprocket wheels and cam caps in order not to in-

terchange them upon refitting.

•

Undo and remove the eight cam cap

screws working in a diagonal se-

quence and in stages.

•

Remove the cam cap carefully so as

not to go through it and damage the

seats of the calibrated dowels.

•

Remove the camshafts with the gears.

DORSODURO FACTORY ABS

Engine

ENG - 209

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды