APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 239

Страница: 239 / 379

The tone wheel is fixed with Loctite threadlock

and must therefore be heated with a special hot

air gun, taking particular care not to heat ex-

cessively.

•

Remove the speed sensor tooth with

the special tool.

When refitting, fix the tone wheel with strong

Loctite threadlock.

Specific tooling

020715Y

Tone wheel removal

•

Undo and remove the selector drum

fastener screw.

•

Remove the selector drum.

DORSODURO FACTORY ABS

Engine

ENG - 239

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды