APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 149 / 379

•

shorted to negative: disconnect the throttle body connector, set the key to ON and check if

PIN 3 is in continuity with the vehicle ground connection: if it is, there is a short circuit in the

cable ground connection; if it is not, replace the throttle body.

•

open circuit, overcurrent, excessive inside temperature: check the throttle body connector

and the throttle control unit connector. If not OK, restore. If everything is OK, disconnect the

throttle body connector (PIN 3) and the throttle control unit connector (C1) and check the

circuit continuity between the two terminals; if there is no continuity, restore the cable har-

ness. If there is continuity, with the throttle body connector connected, check that the

resistance, from the throttle control unit connector, between PIN A1 and C1 is within 1 and

2.5 Ohm; if it is not, replace the throttle body; if it is, check that the throttle body is not

mechanically blocked: if blocked, solve the problem and replace the body; if it is not, replace

the throttle control unit.

Rear throttle supply voltage during self-acquisition P0184

Example value:

low supply voltage

Error cause

•

The throttle power supply voltage is too low to carry out the self-acquisition test correctly (at

each key ON). The instrument panel does not indicate the presence of this error even in the

ATT status.

Troubleshooting

•

The throttle test is not carried out when the key is set to ON because the test could show

unreal errors (because the voltage is too low). Voltage is detected by the Marelli control unit.

Rear throttle control circuit P0186

Example value:

short circuit to positive / short circuit to negative / open circuit, overcurrent, excessive

internal temperature.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 8A of the throttle control

unit connector. If shorted to negative: no voltage has been detected. If the circuit is open,

there is overvoltage or excessive internal temperature: an interruption or excessive ampere

input or control unit overheating has been detected.

Troubleshooting

•

shorted to positive: disconnect the throttle body connector, set key to ON and check voltage

at PIN 3: if the voltage read is higher or equal to 5V, there is a short circuit on the cable

harness; replace the throttle body if the voltage is null.

•

shorted to negative: disconnect the throttle body connector, set the key to ON and check if

PIN 3 is in continuity with the vehicle ground connection: if it is, there is a short circuit in the

cable ground connection; if it is not, replace the throttle body.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 149

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды