APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя страница 85

Страница: 85 / 379

•

29 - VOLTAGE TO THE YELLOW/PINK CABLE OF THE RETENTION RELAY (START-UP

LOGIC) 39

OK, go to 30; NOT OK, go to 31

•

30 - WITH THE RETENTION RELAY (START-UP LOGIC) 39 DISCONNECTED, KEEP

THE STARTER BUTTON PRESSED AND CHECK IF THERE IS APPROX. 1-2V VOLTAGE

IN THE YELLOW/RED CABLE

OK, go to 32; NOT OK, go to 33

•

31 - RESTORE THE CABLE HARNESS

•

32 - CHECK THE GROUND CONNECTION OF THE BLUE CABLE OF THE RETENTION

RELAY (START-UP LOGIC) 39

OK, go to 34; NOT OK, go to 35

•

33 - RESTORE THE CABLE HARNESS

•

34 - CHECK THAT THE RETENTION RELAY (START-UP LOGIC) 39 WORKS COR-

RECTLY

OK, go to 36; NOT OK, go to 37

•

35 - RESTORE THE CABLE HARNESS

•

36 - CHECK CONTINUITY OF THE PINK/BLACK CABLE OF THE RETENTION RELAY

(START-UP LOGIC) 39 TO PIN 14 VEHICLE CONNECTOR

OK, go to 38; NOT OK, go to 39

•

37 - REPLACE THE RETENTION RELAY (START-UP LOGIC) 39

•

38 - CHECK THE VEHICLE CONNECTOR (PIN 14)

OK, go to 40; NOT OK, go to 41

•

39 - RESTORE THE CABLE HARNESS

•

40 - REFER TO THE CHAPTER ON "ELECTRICAL SYSTEM/ CHECKS AND CONTROLS/

ENGINE SPEED SENSOR"; FOLLOW THE TROUBLESHOOTING STEPS IN THE SEC-

TION REFERRING TO "NAVIGATOR: ELECTRICAL ERRORS".

CAUTION: failure NOT identified, go to 42; failure identified, END

•

41 - RESTORE THE CABLE HARNESS

•

42 - CHECK INJECTORS AND ENGINE FOR CORRECT MECHANICAL OPERATION,

CHECK FUEL CIRCUIT PRESSURE.

•

43 - WHEN THE STARTER BUTTON IS PRESSED, DOES THE VOLTAGE TO THE YEL-

LOW/PINK CABLE OF THE CONTROL RELAY (START-UP LOGIC) 40 REACH APPROX.

ZERO?

YES, go to 44; NO, go to 45

DORSODURO FACTORY ABS

Troubleshooting

TROUBL - 85

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Бренды по названию

Популярные бренды