APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 299 / 379

REAR wheel spindle

•

Use a dial gauge to check the wheel

spindle eccentricity (1). Replace the

wheel spindle if the eccentricity ex-

ceeds the limit value (1).

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

REAR WHEEL RIM

•

Using a dial gauge, check that the ra-

dial (A) and the axial eccentricity (B) of

the rim (2) do not exceed the limit val-

ue.

An excessive eccentricity is usually caused by

worn or damaged bearings. Replace the rim (2) if

after replacing the bearings, the value is not within

the specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

DORSODURO FACTORY ABS

Suspensions

SUSP - 299

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды