APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 197 / 379

pos.

Description

Type

Quantity

Torque

Notes

Fastening oil filler plug on Clutch cov-

2 Nm (1.48 lbf ft)

Screw fastening fixing Plate / Clutch

control Mounting

5.50 Nm (4.06 lbf ft)

Screw fastening clutch control

mounting on flywheel side crankcase

half

13 Nm (9.59 lbf ft)

Clutch Cover / Clutch side Cover

TCEI fixing screw (inox protection)

M6x55

10 Nm (7.38 lbf ft)

•

Undo and remove the perimeter fas-

tener screws.

•

Remove the protection plate and the

clutch cover and collect the spacers.

Removing the clutch cover alone is only recom-

mended when replacing the clutch plates. When

removing the entire clutch assembly, removing the

clutch side crankcase is recommended.

However, removing the entire clutch assembly is

possible by removing the clutch cover alone. In this

case, proceed as follows:

•

measure the projection of the clutch

housing from the crankcase before dis-

assembling;

•

when refitting, check that the projection

has not changed before tightening the

clutch nut. If the projection has

changed, rotate the crankshaft to cor-

rectly engage the engine oil pump drive

gear on the clutch housing with the oil

pump driven gear.

DORSODURO FACTORY ABS

Engine

ENG - 197

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды