APRILIA DORSODURO FACTORY ABS 2011 Скачать руководство пользователя

Страница: 142 / 379

connector and check if there is voltage at PIN -: if there is voltage, restore the filter box cable

harness. If there is no voltage, replace the sensor.

•

shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the grey/red cable: if there is voltage, restore the cable harness

between the filter box connector and the Marelli control unit; if there is no voltage, reconnect

the connector and disconnect the injector connector and check if there is a ground connec-

tion on PIN -: if there is voltage, restore the filter box cable harness. If there is no voltage,

replace the injector.

•

the circuit is open: check the component correct electrical characteristic: if it is not correct,

replace the component; if it is correct, check the filter box small connector, the connector on

the component and the Marelli control unit connector: If not OK, restore. If OK, check cable

continuity between the ENGINE PIN 34 and component PIN - and restore the cable harness.

Coil

COIL

Function

Spark generation.

Operation / Operating principle

Inductive discharge system.

Level in electrical circuit diagram:

coils and in-

jectors.

Location:

•

on the vehicle: on the cylinder head

•

connector (if available): -

Electrical characteristics:

•

Primary circuit resistance: approx. 1

Ohm at 20°C between PIN 1 and 3.

•

Secondary circuit resistance: MOhm

value range (with positive probe on

coil).

Pin-out:

1. batt V

2. Secondary circuit ground connection

3. Activation from control unit

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 142

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды

APRILIA DORSODURO FACTORY ABS 2011, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO FACTORY ABS 2011

Отзывы:

Похожие инструкции для DORSODURO FACTORY ABS 2011

Бренды по названию

Популярные бренды