manualshive.com logo in svg

Aerotech UNIDEX 600 Series, Руководство пользователя

Этот продукт Aerotech UNIDEX 600 Series включает в себя бесплатное руководство пользователя для облегчения управления устройством. Скачайте его с нашего сайта, чтобы получить всю необходимую информацию для работы с продуктом. {вставьте ваш веб-сайт здесь}

Поделиться
Скачать
background image

Parameters

U600 User’s Guide

C-78

Aerotech, Inc.

Version 1.4

the FeedHold task parameter is ignored. This task parameter is sampled at the rate
indicated by the AvgPollTimeSec global parameter.

C.4.47.

GlobalEstopDisabled

This task parameter will disable the Global opto-isolated E-stop input from halting the
program running on this task, if it is set true (1).

C.4.48.

HaltTaskOnAxisFault

If this task parameter is set to 1, then the task will generate a ‘Physical Axis Fault’ when
any axis fault occurs on an axis bound to that task. This allows the user to cause a CNC
program to halt when an axis fault occurs. If the parameter is set to zero, axis faults will
not generate task faults, which would stop the CNC program on that task.

C.4.49.

IgnoreAxesMask

This task parameter is used for a form of debugging, which allows you to run a CNC
program without moving certain axes. Its value indicates a set of axes that will be ignored
during motion. That is, the controller will behave as though the indicated axes were not in
the move command. This parameter applies to all motion, including synchronous,
asynchronous, and camming.

It should be differentiated from the SIMULATION axis parameter, in that the move
command will not take the time necessary to move the axis (see example below,
specifically the difference between behavior of X and Z axes.).

Example:

G91 G70 F10

; 10 inches/minute

IgnoreAxesMask = 1

; X axis is ignored

SIMULATION.Z = 1

; Z axis is in simulation

G1 X10

; This command is ignored, takes no time to execute

G1 X10 Y10

; X ignored in this command, Y moves, command
; takes 1 minute

G1 Z10

; Z axis is not moved, but this command takes 1
; minute to execute

G1 Z10 Y10

; Z axis not moved, Y moves, command takes 1.414
; minutes

C.4.50.

InterruptMotion

Setting this task parameter to 1 will cause the CNC to feedhold all axes bound to the task.
After feedhold has completed, you may move the axes via any valid Immediate Mode
commands. The interrupt mode may be exited, by resetting the InterruptMotion task
parameter back to zero. The way that the interrupt mode exits, depends on the setting of
the InterruptMotionReturnType task parameter. If the InterruptMotionReturnType task
parameter defines that interrupted motion is to be resumed, then feedhold is released.

Содержание UNIDEX 600 Series



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UNIDEX 600 Series

Farris Engineering 2600 Series General Installation And Maintenance Instructions preview
2600 Series
Бренд: Farris Engineering Страницы: 12
Eastern Times Technology BT-100 Quick Start Manual preview
BT-100
Бренд: Eastern Times Technology Страницы: 4
Vacon 10 Quick Manual preview
10
Бренд: Vacon Страницы: 18
CAME G5000 Installation, Operation And Maintenance Manual preview
G5000
Бренд: CAME Страницы: 32
Babybee Prams Comet Instruction Manual preview
Comet
Бренд: Babybee Prams Страницы: 21
Baby Trend 7548 Instruction Manual preview
7548
Бренд: Baby Trend Страницы: 8
Baby Trend 7311 Instruction Manual preview
7311
Бренд: Baby Trend Страницы: 19
Baby Trend 1305 Instruction Manual preview
1305
Бренд: Baby Trend Страницы: 5
Baby Trend 1140RC Instruction Manual preview
1140RC
Бренд: Baby Trend Страницы: 4
Harmonic Drive LA Series Manual preview
LA Series
Бренд: Harmonic Drive Страницы: 25
Nelson MR Technical Application Manual preview
MR
Бренд: Nelson Страницы: 8
Salda FLEX Service Manual preview
FLEX
Бренд: Salda Страницы: 20
IBM ServeRAID-MR10is User Manual preview
ServeRAID-MR10is
Бренд: IBM Страницы: 94
IBM ServeRAID-4 Ultra160 Series Installation Instructions Manual preview
ServeRAID-4 Ultra160 Series
Бренд: IBM Страницы: 20
IBM 8271 Nways Ethernet LAN Switch Manual preview
8271 Nways Ethernet LAN Switch
Бренд: IBM Страницы: 6
IBM 3174 Introduction Manual preview
3174
Бренд: IBM Страницы: 86
IBM 3745 Series Console Setup Manual preview
3745 Series
Бренд: IBM Страницы: 205
IBM N6000 Series Installation And Setup Instructions preview
N6000 Series
Бренд: IBM Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды