Adaptec 2254100-R - SATA RAID 2410SA SGL/64 Controller Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 233

Adaptec 2254100-R - SATA RAID 2410SA SGL/64 Controller Скачать руководство пользователя страница 100

5-61

container Commands

Rebuild

A rebuild task is running on the specified array.
Typically, the rebuild task runs when the controller is
in a rebuild for a redundant array (RAID-5 set, mirror
set, or multilevel array of mirror sets).

Reconfg

An array reconfigure task is running on the specified
array. When the array reconfigure task completes, the
specified array becomes a different array (for example,
from a volume set to a stripe set). The array
reconfigure task runs as a result of using the

container reconfigure

command.

Scrub

A scrub task is running on the specified redundant
array. When the scrub task completes, the specified
redundant array has reconstructed data on one
partition based on data found on the other partition
(for mirror sets and multilevel arrays of mirror sets).
Or, the specified redundant array recalculates and
replaces, if necessary, the parity information (for
RAID-5 sets). The scrub task runs as a result of the

container scrub

command. The scrub task also

runs as a result of the

container create raid5

command with the

/scrub

switch specified.

Verify

A verify with no repair of bad blocks task is running
on the specified SCSI disk. When the verify with no
repair of bad blocks task completes, the specified SCSI
disk’s blocks were verified without repairing any
detected defects. The verify with no repair of bad
blocks task runs as a result of using the

disk

verify

command without specifying the

/repair

switch.

VfyRepl

A verify with repair of bad blocks task is running on
the specified SCSI disk. When the verify with repair of
bad blocks task completes, the specified SCSI disk’s
blocks are verified with repairs. The verify with repair
of bad blocks task runs as a result of using the

disk

verify

command with the

/repair

switch.

Zero

A clear disk task is running on the specified SCSI disk.
When the clear disk task completes, the specified SCSI
disk is cleared (that is, all data is erased and cannot be
recovered). The clear disk task runs as a result of using
the

disk zero

command.

Table 5-4. Task Types (Continued)

Task

Meaning

«
...
98
99
100
101
102
...
»

Содержание 2254100-R - SATA RAID 2410SA SGL/64 Controller










































































































































































































































Отзывы:

Нет отзывов