Xerox Legacy 4112 System Administration Manual Download Page 324

Page: 324 / 364

Xerox 4112/4127 Copier/Printer System Administration Guide

9-2

9. Troubleshooting

When you cannot print

You cannot delete documents from the Printer window.

Notes and Restrictions

The following are the notes and restrictions for using SMB:

Configuration on the Machine

•

Take maximum care with the IP address settings. IP

addresses are managed throughout the system as a whole.

The configuration should be performed only after consulting

with your network administrator.

•

Subnet Mask and Gateway addresses may be necessary

depending on the network environment. Confirm with the

network administrator and set up the necessary items.

•

When the port status is set to Enable, it sometimes

Cause

Check point

Remedy

The machine is processing a

request from a different computer.

(Only when the machine is set to

the

Non-Spool

mode)

Confirm the machine is processing

a print job. (A write error dialog

should be displayed to indicate

that there is no room for the print

queue available.)

Wait until the machine finishes

processing the print job, or change

the machine setting to

Spool

mode.

The number of connections to the

machine exceeded the maximum

connections allowed.

Confirm if the machine is

processing simultaneous

processing requests (print

requests, status queries, etc.) from

multiple computers. A write error

dialog should be displayed to

indicate that no more remote

computers can be connected.

Wait for a while and retry printing.

Cause

Check point

Remedy

You are trying to delete all print

data displayed in the

Printer

window. (Only the system

administrator is allowed to do this

task.)

Confirm whether you are trying to

delete the print data from the

Printer

menu. (In Windows OS:

Clear Print Jobs

menu.)

Select the print data to be deleted,

and delete from the

Document

menu in the

Printer

window.

(

Cancel Printing

menu.)

The print data has a different

owner.

Confirm if the name displayed as

the Owner for the selected print

data and the login name for the

user to Windows are the same.

of the document owner and delete

the print data.

Service Pack 4.0 or later is not

installed.

(For Windows NT 4.0.)

Confirm the Service Pack version

which is displayed when Windows

NT is starting up.

Install Service Pack 4.0 or later.

Summary of Contents for Legacy 4112













































































































































































































































































































































































Search results

Summary of Contents for Legacy 4112

Reviews:

Related manuals for Legacy 4112

Brands by name

Popular brands

Xerox Legacy 4112, System Administration Manual

Search results

Summary of Contents for Legacy 4112

Reviews:

Related manuals for Legacy 4112

Brands by name

Popular brands