![background image](http://html1.mh-extra.com/html/valco-melton/d4/d4_manual_849618029.webp)
MM147 - D4 Hot Melt Unit
Section 4 - Installation
29
Connecting the Hot Melt Hoses to the Applicators
WARNING!
If hand-held applicators are used, care should be taken to ensure safe operation. Heat
protective gloves should be worn. Hot melt is under high pressure at the nozzle tip of the
applicator. Failure to observe could result in personal injury (burns).
WARNING!
If hand-held applicators are used, operators should not work facing each other. Failure to
observe could result in personal injury (burns).
If fixed applicators are used, they should be protected from accidental contact by the
operator. Failure to observe could result in personal injury (burns).
CAUTION!
Hand-held applicators require a suitable hook for hanging while not in use. The hook must
support the weight of the applicator with the hose. Failure to observe could result in damage
to equipment.
Either hand-held or fixed applicators can be used with the unit.
To connect the fixed applicators, follow these steps:
1. Mount the applicator to the desired location on the parent machine.
Do not place applicators where the ambient temperature is low or
where there is a draft.
2. Connect the end of the hot melt hose (Figure 4-3) to the fluid inlet fitting on the applicator (Figure 4-4).
3. Connect the hot melt hose lead assembly’s female connector to the lead assembly on the applicator.
Figure 4-3. Hot Melt Hose
Figure 4-4. Applicator
Fluid inlet fitting
Lead assembly with female
connector (connects to lead
assembly on applicator)
End of glue hose that connects
to fluid fitting on applicator
Summary of Contents for D4
