5
Valco Melton
IS0212
D and S Series Pump Change Procedure
Caution!
Caution!
Caution!
Caution!
Caution!
Install by cross-tightening the four (4) mb x 90 socket-
head cap screws. This will ensure the pump has a
uniform seal with the manifold, and will not leak.
Make sure the Spur Gear is under the sensor, otherwise
the unit will not function properly. If the spur gear is not
under the sensor, loosen the set screw and move the
spur gear to the correct position.
Valco Cincinnati Incorporated
411 Circle Freeway Drive
Cincinnati, Ohio 45246, USA
TEL: (1) 513-874-6550
FAX: (1) 513-874-3612
Melton S.L.U.
Pol. Industrial Agustinos
calle G, n. 34
31160 Orcoyen, Navarra, Spain
TEL: (34) 948-321-580
FAX: (34) 948-326-584
Valco Cincinnati, Ltd.
Unit 7-8
Hortonwood 32
Telford TF1 7YN England
TEL: (44) 1952-677911
FAX: (44) 1952-677945
Valco Cincinnati GmbH
Storkower Strasse 6
D-15749 Gallun, Germany
TEL: (49) 33764 8700
FAX: (49) 33764 87070
No part of this document may be reproduced without express permission from Valco Cincinnati, Inc. All rights reserved. Designs and other information may change without notice.
© 2013 Valco Cincinnati, Inc.
www.valcomelton.com
IS0212 4/13
To Replace an S
Series Unit Pump
1.
Remove the right-side and lower-front panels from the unit by
turning the latch and lifting up on the handle.
Warning!
Warning!
Warning!
Warning!
Warning!
Make sure the unit is at room temperature.
2.
Loosen, but do not remove, the set screw on the love joy coupling
closest to the pump.
3.
Loosen, but do not remove, one of the screws on each of the shaft
collars, and on both sides of the motor.
4.
Slide the shaft away from the pump until the coupling is no longer
on the shaft.
5.
Remove the four (4) m8 x 90 socket-head cap screws from the
pump.
6.
Remove the pump and O-rings.
7.
Install the new pump by reversing the above procedures.
Summary of Contents for D4
