MM147 - D4 Hot Melt Unit
Section 6 - Operation
95
Temperature Status LEDs - Continued
If the temperature set points are not correct or need to be adjusted, select the appropriate zone and adjust the
temperature setting (see Section 5 – Setup for setting temperatures). The system is ready (and the System Ready
LED illuminates green) when all zones reach their respective temperature setpoints minus the System Ready
Temperature Offset.
The system ready signal enables the pump motor. This prevents the pump motor from being activated before the
adhesive in the pump has softened.
Consult the adhesive data sheet to find the softening point temperature of the adhesive.
Pump Operation
When the pump is enabled but waiting on the System Ready LED to
illuminate green, the pump symbol flashes in the status bar.
Pump On/Off Key
The Pump On/Off Key is the master enable for the Pump(s). It can be set to come on automatically when the unit is
ready (see Section 5 - Setup, “Auto Pump Enable”). Note that all temperatures must reach the system ready
temperature and the Ready LED must be illuminated green for the pump to operate.
Pump Status Key
Fixed Speed Unit
The Pump Menu Key will give you access to this screen where the Pump RPM is shown and the individual pump can
be enabled.
Pump Symbol (flashes)
Pump On/Off LED
Status Bar
Pump On/Off Key
Pump Menu Key
Navigation
Keys
Summary of Contents for D4
