![background image](http://html1.mh-extra.com/html/valco-melton/d4/d4_manual_849618232.webp)
IS0299 - D Series Coupling Upgrade Procedure
8
14. Replace the key in the motor shaft if removed earlier.
15. Place the new ¾” bore jaw coupling hub (783XX371) on the motor shaft. Do not tighten the set screw
yet, as the motor side hub needs to be positioned after assembly.
16. Using the 1/4-28 hex head cap screws provided (884XX004) and 1/4 split lock washers provided
(798XX735), fasten the motor to the new motor bracket. Tighten all screws by hand to seat the motor,
then use a torque wrench to tighten each screw to 106 in-lbs (12 N-m).
17. Manually rotate the motor shaft as needed in order to align the jaws of both couplings with the spider.
18. Slide the jaw coupling hub on the motor shaft toward the pump, engaging the spider. Verify that the hub
slides freely when engaging the spider. With the jaw coupling hub on the motor shaft just touching the
spider, tighten the set screw in the jaw coupling hub using a 1/8 tee handle hex key.
CAUTION!
If the hub does not slide freely when engaging the spider, the pump and motor shafts may not
be properly aligned. Proceeding without correcting misalignment could cause damage to the
pump!
Summary of Contents for D4
