![background image](http://html1.mh-extra.com/html/valco-melton/d4/d4_manual_849618025.webp)
MM147 - D4 Hot Melt Unit
Section 4 - Installation
25
Connecting the Electrical Power
WARNING!
Electrical connections should be made only by experienced service personnel! Failure to
observe could result in personal injury, death, or damage to equipment.
When connecting the supply of electrical power, follow these guidelines:
•
Connect the unit to a “clean” supply of electrical power. Use a dedicated circuit if possible.
If a dedicated circuit is not available, do not connect the unit to a
circuit that supplies high-amperage equipment—use another circuit
such as a lighting circuit. Otherwise, equipment may not function
properly.
WARNING!
The external power source must be turned off before connecting power to the unit! Failure to
observe could result in personal injury, death, or damage to equipment.
WARNING!
Only experienced service personnel should connect power to the unit! Failure to observe
could result in personal injury, death, or damage to equipment.
The use of an earth-leakage or ground-fault power breaker is recommended with this unit.
This unit must be earthed or grounded. Failure to observe could result in personal injury,
death, or damage to equipment.
The D4 hot melt unit can be set up to use one of the following power sources:
Incoming Electrical Service
Power Connector
Terminals
Voltage Plug
Connector Label
A
B
C
D
PE
Part No. / Color
Part No. / Color
380VAC 3-phase with
Neutral (4 wire service)
3/N/PE AC
400/230V
L1 L2 L3 N PE
029XX437
Blue
782XX262
Blue
200 to 240VAC 3-phase w/o
Neutral (3 wire service)
3/PE AC
200-240V
L1 L2 X L3 PE
029XX435
Black
782XX260
Black
200 to 240VAC 1-phase w/o
Neutral (2 wire service)
1/PE AC
200-240V
L1 X X L2 PE
029XX436
White
782XX261
White
The system should be connected via a suitable type of flexible conduit from a supply isolator and ground-fault power
breaker. The supply should be clean and free from excess interference from other machines.
WARNING!
You MUST follow these steps to connect power to the unit, or personal injury and/or damage
to the unit may result.
1. Open the electrical enclosure door.
2. Route the power cable through the cable clamp in the chassis of the unit. The power cable must meet
the minimum requirements given in the chart above.
3. Referring to the chart above, locate the appropriate voltage selector plug and power connector label
corresponding to the incoming electrical service.
Summary of Contents for D4
