MM147 - D4 Hot Melt Unit
Section 4 - Installation
23
Section 4 - Installation
Choosing a Location
The D4 hot melt unit is assembled at the factory. However, the power and the glue hoses must be connected by the
customer. This section contains instructions for making the necessary connections.
While choosing a location for the unit, keep in mind that:
•
Service personnel will need access to the left and right sides of the unit for electrical service, and the
back of the unit for changing the glue hoses and filter.
•
The operator needs easy access to the front operator panel.
•
If the unit will not be moved from one location to another, it should be screwed or bolted to a suitable
stable, flat, level surface.
•
The unit should have clearance around the outside of the case to allow air to circulate freely around it.
•
The unit should have clearance above the top of the unit so it may be filled easily without obstruction
to the operator.
•
The location should be near the glue station so that the glue hoses can be routed to the applicators in
as straight a line as possible.
•
The location for the unit should be clean. Dirt in the glue tank causes clogging of the applicator
nozzles.
•
The unit should be protected from high and low ambient temperatures, as well as from rapid changes
in ambient temperature.
•
The unit must be protected from condensate and water.
•
The unit must be protected from strong vibrations.
•
The tank lid must be able to open fully back so there is no danger of it falling onto operator’s hands
while filling.
Summary of Contents for D4
