![background image](http://html1.mh-extra.com/html/valco-melton/d4/d4_manual_849618210.webp)
IS0344
Anybus Installation and Setup
2 ValcoMelton
Physical Installation - Continued
ITEM NO.
DESCRIPTION
PART NO.
QTY.
1
PCB ASSEMBLY; ANYBUS I/O EXTEND
BJK0347
1
2
MODULE, ANYBUS, ETHERNET/IP, JTS0021
098XX123
1
3
SPACER, PCB 14MM LONG, SNAP IN NYLON
091XX644
1
4
STANDOFF,6MM HEX, M3 X 0,5 THREAD
091XX563
2
5
SCREW BUTTON HEAD CAP M3 X 6
784XX541
2
6
CABLE RIBBON 30P 2MM M/M 2.0" *
BJK0389
1
*Ribbon Cable is only needed for 151xx650 Control Boards.
Configuring the Melt Unit
The Communication Interface can be enabled and set up in the Melter CONFIG menu. When any of these network
settings are changed, the Melter must have the power reset in order for the new address to take effect. The default
network settings are shown below. The network settings should be changed to match your network.
Remote Communication:
The interface can be enabled by changing the Protocol from
Disabled
to
Ethernet IP
. The
operation mode should also have “Local” selected, as shown below.
Network Settings:
The network settings should be configured for your network. The default settings are shown
below.
Installation and Setup are completed.
Configuring PLC for Ethernet/IP Communication
Using the Correct EDS File
Many vendor EtherNet/IP configuration tools support importing an EDS file, and then uses the contents of this file to
correctly configure a number of internal settings. Some configuration tools, however (most notably RSLogix 5000 as
of this writing), do not use EDS files to configure EtherNet/IP I/O connections.
Summary of Contents for D4
