MM113 - D10/D16 Hot Melt Unit
Section 5 - Setup
87
PID Setup Menu
PID Settings
The PID settings are factory set for each zone. The factory PID settings complement Valco Melton’s Tank, Hose, and
Gun watt densities (Tank 1 screen shown. Use left/right keys to access other screens).
CAUTION!
Changing these settings is not recommended. Changes should be made only by authorized
ValcoMelton personnel.
In the case where a special temperature zone is used (example: coating head) and its temperature does not regulate
properly, the Auto Tune function can be used to set the PID settings.
Default PID Settings
Zone Type
P
I
D
S
R
Tank
80 3 10 10 9
Hose
80 5 10 10 9
Gun
80 5 10 10 9
AutoTune Feature
The Auto Tune feature will optimize the PID settings for each zone that is enabled when the Auto Tune is started. The
Auto Tune feature can take up to eight hours to complete and the power must not be turned off during this process. It
is recommended to only enable zones that need their PID values adjusted to reduce the time taken for tuning.
The AutoTune Feature is located in the PID Screen and can ONLY be accomplished under the password Level 3!
Changing out gun/hose pairs or moving a gun or hose from it’s
original AutoTune position, will require that AutoTune be run again to
optimize the PID settings again.
X5
Summary of Contents for D10
